MOTOGADGET MO.VIEW
BAR-END MIRROR, PIECE
Important notes
MOTOGADGET MO.VIEW BAR-END MIRROR, PIECE
motogadget revolutionised the rear-view mirror with its invention of the mo.view range of glassless mirrors. With these mirrors, the reflective surface is actually machined into the aluminium body using a special diamond-grinding process on ultra-precision machines. This method creates a "weightless" design with no border or frame. The mirror body itself is very slim and lightweight. As exemplified by the motogadget mo.view *sport 60* bar-end mirrors.
mo.view *sport 60* mirror is compact, with pared-down lines, and it goes perfectly with many other motogadget accessories. It is ultra-flat and free of any distortion.
This mirror can be mounted either above or below the handlebar. The short stems can be swivelled. The mirror is suitable for the right and left end of the handlebar. It is attached directly to the bar end (22 mm and 1 inch) or using the mo.view *bar adapter* if the grips or controls cannot be moved.
- Material: Anodised aluminium, CNC-machined
- Weight: approx. 128 g
- Diameter of clamp: suitable for 22 mm and 1 inch imperial handlebars
- Width of clamp: 10 mm
- Dimensions in mm (see dimensional sketch): a = 83, b = 122, c = 150, d = 110
- E-approved
mo.view *sport 60* Rear-View Mirror (with ECE marking), complete with stem, clamp and instructions
Cleaning: Use a mild detergent and a microfiber cloth to remove dirt, dust and other residues from the surface of the mirrors. Avoid abrasive cleaning agents that could damage the surface.
High Class Instruments & Accessories - MADE IN GERMANY
Anyone who is serious about customising cannot fail to appreciate the quality of motogadget products. In no time at all, the Berlin-based manufacturer has achieved virtually cult status with its high-class instruments. The reason is the exceptional functionality of motogadget products, but most importantly their extremely clean design, high-quality materials, top engineering and absolute reliability.
Modern vehicle accessories of different types now frequently carry an "E" approval mark valid throughout Europe. This "E" mark, which is made up of a combination of letters and numbers, is clearly displayed on the product and shows the application tested, the country in which testing was carried out and, where appropriate, the vehicle type to which approval applies. EC type approval for exhaust systems, for example, are always issued for a specific vehicle type, whereas in the case of lighting, they apply to an entire group of vehicles, e.g. motorcycles.
This certification mark is the sole proof of legality stipulated by law, i.e. no written report or entry in the vehicle documents by TÜV (German Technical Inspection Association) is required. However, when it comes to installing accessories, the relevant guidelines of the Road Traffic Licensing Regulations (StvZO) must always be observed.
At at a roadside check or a TÜV vehicle inspection, the registered keeper is only required to show the "E" mark. It is then up to the official in charge whether to check the mark with the Federal Motor Transport Authority (KBA) in Flensburg (or equivalent type approval authority in other countries), which is able to decode all certification marks.
Original parts on newer vehicles that have been given an "E" mark at the factory may only be replaced with accessories that have likewise undergone E-approval. An E-certified mirror may not, for example, by replaced with a mirror that only has TÜV approval under the German vehicle licensing regulations.
This product is made of high-quality CNC-machined aluminium and will look great on your motorbike.
To ensure that it gives you many years of service, please observe the following care instructions:
1. After installing the product, and each time you wash your motorbike, apply a wax-based care product, e.g. Procycle Polishing Wax, Order no. 10004923 for protection against wind and weather. You may need to repeat the application after an outing in winter weather, rain or salty air (near the coast).
2. Remove any corrosion as soon as possible using a standard aluminium polish (e.g. Autosol Aluminium Polish, Order no. 10004421).
QUALITY MADE IN GERMANY!
By purchasing this item you have chosen a premium-quality product with superior German workmanship. This internationally acknowledged mark of quality means that this product is the result of efficiently coordinated development and production processes, technological expertise, continuous quality controls.
Dimension sketch mirror
To ensure that your objective and truthful report will be really beneficial to all readers, please observe the following rules.
- Please only rate products that you have personally used for their intended purpose.
- Please give reasons for your positive and negative criticisms. Only then will they benefit other customers and allow us to improve the product if necessary.
- Please don’t copy content that has already been published elsewhere. It’s your personal experience which counts.
- Data protection: Please don’t include your own and other people’s addresses, telephone numbers or URLs or even the names of third parties (people as well as companies) in your review.
- In your product review, please don’t make comparisons with third party product ranges. Regardless of whether you judge these positively or negatively, you, or we as operators of this online shop, would be violating competition law.
Fair play: Please follow these rules so that we don’t have to shorten or delete your rating.
Your product rating has been saved. It will be displayed in a few minutes
Do you really want to cancel your entry?